coil power at pickup voltage 1 coil: 256 mw (typical) 2 coils: 384 mw max. continuous 1 coil: 0.4 w dissipation 2 coils: 0.6 w temperature rise 26c (47f) at nominal coil voltage max. temperature 130c (266f) notes 1. all values at 23c (73.4f). 2. relay may pull in with less than ?must operate? value. 3. speci cations subject to change without notice. 4. check the relay set/reset state before energizing the relay in application. general data life expectancy minimum operations mechanical 1 x 10 6 electrical 1 x 10 5 at 16 a 250 vac res. set time (typical) 15 ms at nominal coil voltage reset time (typical) 15 ms at nominal coil voltage (with no coil suppression) min. pulse time 75ms max pulse time 1 min. dielectric strength 4400 vac coil to contact (at sea level for 1 min.) 1000 vac between open contacts surge voltage coil to contact 10,000v (at 1.2x50 s) insulation 1000 megohms min. at 20c resistance 500 vdc 50% rh ambient temperature at nominal coil voltage operating -40c (-40f) to 85c (185f) storage 0c (32f) to 40c (104f) vibration 0.062" da at 10?55 hz shock 10 g enclosure p.b .t . polyester terminals tinned copper alloy, p. c. max. solder temp. 270c (518f) max. solder time 5 seconds max. solvent temp. 80c (176f) contacts arrangement spdt (1 form c) spst (1 form a, 1 form b) ratings resistive load: max. switched power: 5000 va max. switched current: 20 a max. switched voltage: 277 vac rated load ul, cur 20a at 250 vac, resistive, 20k cycles [1] 16a at 250 vac, resistive, 100k cycles [1] 1.5 hp at 250 vac, motor, 6k cycles [1] .5 hp at 120 & 250 vac, motor, 20k cycles (form a) [1] tv-8 at 240vac, 25k cycles (form a) [1] tungsten 1662w 6a at 277vac, 6k cycles (form a) [1] tungsten 1800w 15a at 120vac, 20k cycles (form a) [1] electronic b a llast 1800w 15a at 120vac, 20k cycles (form a) [1] standard b a ll as t 1662w 6a at 277vac, 6k cycles (form a) [1] ?t? high inrush version (form a 5.0mm only) 3300w at 277vac, electronic ballast, 20k cycles [2] 3000w at 220vac, tungsten, 6k cycles [2] 1500w at 347vac, std. ballast, 20k cycles [2] material [1] silver tin oxide, [2] tungsten/silver tin oxide resistance < 50 milliohms initially (at 1a, 24 vdc) az762p 20 a spdt miniature power relay latching relay dielectric strength 4400 vrms epoxy sealed versions available 20 amp switching high inrush current 500a / 2ms available ul, cur le e44211 11/17/15 weight 13 g features
coil specifications - dual coil latching order number* nominal coil must operate max. continuous coil 1 coil 2 unsealed sealed vdc vdc vdc resistance 10% resistance 10% 3 2.4 3.9 15 15 az762p2?1ce?3d az7 62p2?1ce?3de 5 4.0 6.5 42 42 az762p2?1ce?5d az7 62p2?1ce?5de 6 4.8 7.8 60 60 az762p2?1ce?6d az762p2?1ce?6de 12 9.6 15.6 240 240 az762p2?1ce?12d az762p2?1ce?12de 24 19.2 31.2 886 886 az762p2?1ce?24d az762p2?1ce?24de relay ordering data coil specifications - single coil latching order number* nominal coil must operate max. continuous coil unsealed sealed vdc vdc vdc resistance 10% 3 2.4 3.9 22.5 az762p1?1ce?3d az762p1?1ce?3de 5 4.0 6.5 62.5 az762p1?1ce?5d az762p1?1ce?5de 6 4.8 7.8 90 az762p1?1ce?6d az762p1?1ce?6de 12 9.6 15.6 360 az762p1?1ce?12d az762p1?1ce?12de 24 19.2 31.2 1,440 az762p1?1ce?24d az762p1?1ce?24de az 11/17/15 az762p * substitute ?1a? or ?1b? in place of ?1c? for form a or b respectively. form a relay is in the reset postion. form b relay is in the set position. add suffix ?k? for 3.5mm pin spacing version. replace ?1ae? with ?1at? for w+agsno2 high inrush contacts ( form a, 5. 0mm pin spacing only). add suffix ?l? for 2.5mm pin spacing version. note, form c only available in 5.0mm and 3.5mm pin spacing. add suffix ?r? for reversed polarity coil. wiring diagram
az762p 11/17/15 dimensions in metric. mechanical data 5.0mm spacing - standard no terminal for single coil version no terminal on 1 form a no terminal for no terminal on single coil version 1 form a no terminal for single coil version 3.5mm spacing - suffix ?k? 2.5mm spacing - suffix ?l? pcb layout viewed toward terminals viewed toward terminals viewed toward terminals
|
